• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your Fiat punto key fob 500 Key Fob Won't Work

A key fob for fiat key fob 500 allows you to easily open doors and start your car. There are a myriad of reasons the fob won't work. These include a dead battery or water damage, receiver module issues, and interference.

This listing is for a NEW replacement fiat key replacement Flip Key Remote - like the Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that the 500 key fob won't function is a dead battery. Modern key fobs only have only a limited range of operation and must be within only a few inches from the vehicle to work. If you are far from your car and press the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this occurs you need to replace the battery of your coin-cell (Part Number CR2032) by a new one of a reputable brand like Panasonic Duracell or Energizer. You can find them at your local hardware store, or on the internet.

You can test the battery in the coin-cell by pressing the buttons while you are standing close to your fiat car key 500. The parking lights will flash and the key fob should operate the lock and unlock switches.

If the fob's remote doesn't function after replacing the battery, it could have water damage that prevents it from connecting to the receiver module inside your car. Water damage can occur in a number of ways, ranging from small splashes to submerging the fob salt water at the beach. If you think your fob was exposed to water, place it in a rice bag to draw out the moisture. If this doesn't work, you will have to get your fob reset by an auto locksmith or dealer.

Water Damage

Water damage can occur when you immerse the fob into the ocean or wash it in a machine. Saltwater poses a particular risk to the circuit board of the fob that can cause it to short out and eventually die. Getting the fob wet is not an ideal choice but if you accidentally drop it in a cup of water or do not remember to take it out of your pocket before you run the washer do not give up hope.

First take the battery off the fob. Clean the electronic chip using isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Test the fob afterward to check if it's working. If the key still doesn't work, it may have to be programmed again. This is usually handled by an auto locksmith or dealer.

If the key is a newer model and has never been programmed to your car It will most likely need to be replaced completely. This is a straightforward process that can be completed by a professional automotive locksmith. The locksmith will need the key cut to match your vehicle's ignition. They will also need to program the fob into the car's system. This is an affordable and quick procedure that can be completed on the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob could stop working is because it's out of range. The remote's range is of 30 feet. Therefore, in the event that you are far from your car it won't respond to your commands. It is possible to remedy this by moving your remote closer to your vehicle until it responds.

If your fob does not work after you replace the battery inside the coin, which is also known as a "button", "watch" or "button" It may be due to a malfunction on the circuit board inside. Reprogramming the fob typically resolves this problem. You can find the instructions for the majority of vehicles on YouTube or in the owner's guide.

It is possible to replace the metal retaining clips that hold the battery of your coin in place. If they lose tension, it could hinder the battery from being properly seated and could cause your remote to malfunction.

In rare cases the fob might become desync'd with your vehicle due to software or hardware issues. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases the software might require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit signals. This could occur if the keyfob's location is in close proximity to a radio transmitter like a cellphone or radar detector. The key fob could not function because of a problem to the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. battery replacement, reprogramming and using the spare key fob, you could have a defective receiver module on your 500. The receiver module, located under the dashboard, is able to pick up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting every single system on board in your 500 and include the key fob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable and then the positive cable. Reconnect the battery. This will remove any remaining electricity, and allow you to restart the computer of your car. This could help you get your key fob to work again. If the issue continues, you should speak with an expert technician. They can determine the exact cause of your issues.