• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps allow your pet leave and come as they please without having to let him in or out. They also can help stop your cat from peeing in the house.

Fitting a cat flap in the door panel made of upvc is much easier than in glass doors, however it does require some skills and the appropriate tools.

Take a look at the Door

The installation of a cat flap inside the door can be a challenge however, as long as you choose the right type of cat flap, take your time and follow the instructions provided it shouldn't be a problem. We will show how to trace the shape, use an jigsaw for cutting out the area in the door and then finish the job by attaching the cat flap to the door. This will ensure the flap stays in position and protects the doors from damage caused by wind and rain.

To determine the size of the cat flap you require, take a measurement of your pet's width. This will let you choose a cat flap that is large enough for your pet to enter the house and exit without having to open the door every time.

Once you have the measurements you can mark out where on the door the template should be placed, usually, this is done using an X, however some kits include an illustration that outlines where to drill, if yours does then stick it to the door and draw a line around the door. If your door has a moulding or sill on the bottom of it then make sure you have clearance from these as this will ensure your cat's safety and stop them from gaining access to your home.

Put on your eye protection as well as a dust mask. Then using a jigsaw, begin to cut along the line you've drawn in. Don't push the blade too hard because this could cause it to cut faster than you would like it to. If you have a set square then make use of it to verify that you're cutting properly and also to ensure that the hole is a proper rectangle. Once you are satisfied with the shape, you can begin to remove the remaining door material.

Draw a Line

The cat flap allows you to let your pet inside and outside without having to worry about unwanted visitors or unwanted gifts. It also helps prevent draughts and helps keep your home's temperature stable. The installation of a cat flap your door might seem difficult to those who haven't tried it before. A lot of people will hire an expert carpenter or joiner to complete the job. While this is definitely an option, it's possible to do the job yourself if you own the appropriate tools and follow the instructions carefully.

While this is far simpler to accomplish with a wooden door, it is still feasible in uPVC doors - although you must be careful not to scratch the doors since this could invalidate the warranty. First, you need to examine the door's measurements to ensure it will accommodate the new cat-flap. If you have a standard uPVC panel it's easy. However when your door is composite or another type of door, you may have to be more cautious.

The next step is to determine the height of your belly for your cat. This is the measurement from the floor to the underside of the cat flap in upvc door panel's stomach, and you'll need to locate a place on the door where this measurement is within the range that your cat is able to comfortably walk through. Once you've got the information you'll need to mark the area with a spirit-level and a pencil so you are certain that the opening will fit your cat flap installers near me.

After you have marked the area, it is time to make the hole. It is important to take your time and use a jigsaw ensure that the cuts are clean and smooth not rough and uneven. This could damage your door. Wear safety glasses and a dust mask when working with a jigsaw. Inhaling sawdust is hazardous for your health. After you've cut the hole, you will require sandpaper to smooth the edges so that the cat flap can be easily fitted into place.

Make a hole

It can be a challenge to install an animal flap on a door panel or a sealed double glazing unit. It is tempting to do it yourself, but unless have expertise in DIY, it's probably best to get a professional to do the job for you. A mistake could not only be unsightly and unattractive, but could also be an security risk. It could allow cold air in when the cat is outdoors and hot air out when it is inside.

The first thing to do is draw the position of the hole in the door with pencil and an ax level. This will ensure that it is correctly located and is parallel to the other components of the door. Make sure to have sandpaper in your possession to smooth out any rough edges.

After the line is traced, you must cut the hole using a jigsaw. Be sure to wear any safety equipment for working with an electric tool. If you are concerned about the noise of the jigsaw, consider buying an electric version that is quieter and simpler to use.

It is essential to only cut away the material that is required for the fitment of the cat flap. A little bit of extra material is required to increase the thickness of the wall of the flap but removing more than this can cause problems or harm the frame of the door.

If the upvc door features a metal panel or frame, it could interfere with the microchip flap. In this situation you'll need to make an oversize hole to ensure that the metal doesn't come into contact with wall of the flap.

If you're looking to install a cat flap in a upvc or double-glazed window cat flap with frames made of metal, you'll need to consult a specialist. They will provide you with a brand new piece of glass with the hole already made for the cat flap. This will be cheaper than trying to install a cat flap in an existing pane that was not made specifically for this purpose.

Fit the Flap

Cat flaps let your pet come and go as they please, giving them the freedom to lounge inside the house when they feel like it. If you have a uPVC front door, it may be difficult to install a cat flap. This is especially the case in the event that you don't own an glass panel that is cut. If you're looking to install a half-glazed uPVC replacement panel, it is possible to add the cat flap installation flap. It's not as easy as simply making a hole in the door, however there are a few things you'll need first to make sure it's secure.

A composite, uPVC, or GRP door panel typically comprises an extremely thin plastic outer skin that is bonded to a soft, insulating polystyrene core. It is crucial to be careful when cutting the material. This type of door comes with a template that can be used to cut the hole.

Once you have marked the location of the hole in your door, it's time to put in the cat flap itself. You can purchase and install a wide variety of different models including basic push-button operated ones to ones that are activated by microchips that only let in your pet. However, regardless of what kind of cat flap you pick, it's crucial to ensure that your cat can comfortably use the flap without becoming trapped in the weather.

It is a good idea to opt for circular fittings instead of a square one, as circles can be more securely cut into door glass. This is because square holes leave the glass vulnerable to cracking when drilling is applied to it. It's also a much safer option to use as you're not putting yourself at risk by having to drill into toughened glass that might break and injure your pet or your family. This is especially crucial if you have children or elderly people in your home that could be injured by glass fragments.